Operation list of UgCS desktop and UgCS for DJI

From UgCS
Jump to: navigation, search

Main Page UgCS UgCS for DJI User Manual Drone connection and first flight

Download this subcategory as a PDF file

No Step Application in which the Step is performed Notes
1 Create route UgCS desktop To create, plan and calculate mission and routes, use UgCS desktop client.
2 Upload route UgCS desktop To upload the route to drone use UgCS desktop:

• Select drone (start route automatic calculation)
• Press “Upload” button

Pay attention to the remote control mode:
Phantom 3 (Professional, Advanced) – mode “F”,
Phantom 3 (Standard) - RC switch S1 down,
Phantom 4, Phantom 4 PRO / ADV - mode “P”,
Inspire 1, (Professional, Raw) - mode “F”,
Inspire 2 - mode “P”,
M600 / M600 Pro - mode “P”,
M200 - mode “P”,
M100 - mode “F”,
A3, N3 - mode “P”,
Mavic Pro, Mavic 2 - mode “P”,
Spark - mode “P”.
To stop a mission toggle RC switch from "F" to "P".
To stop a Phantom 4 (PRO), mission toggle RC switch from "P" to "S" (Sport) mode.
User should set new home point with caution (see Route settings: home location). A home location is valid if it is within 30m of:
• initial take-off location
• aircraft’s current location
• remote controller’s current location as shown by RC GPS
• mobile device’s current location

*NOTE: Route will not be uploaded if drone has completed the mission. In this case, send “Hold” or “Manual mode” command.
3 Auto – Launch route UgCS desktop or UgCS for DJI Use UgCS desktop or UgCS for DJI to launch route. Press “Auto mode” command in UgCS desktop or “Take-off” button in UgCS for DJI.

After drone has finished the route, “Auto Mode” command will become enabled and the route can be repeated.

*NOTE: For Phantom 3 Standard, ensure RC throttle stick is not locked down!
4 Manual mode UgCS desktop Sets vehicle in manual mode, for example, to control vehicle with RC. This command interrupts mission and erases it from drone memory. New route can be uploaded.
5 Hold UgCS desktop or UgCS for DJI Puts mission on hold. If flown in Click & Go mode - stops the vehicle and clears current target point.
*NOTE: When drone is in 'Hold' mode, operator can move it via RC only along the current pass (only forward and backward of the route allowed).
6 Continue UgCS desktop or UgCS for DJI Continues mission from point where mission was put on hold.
7 Track mission UgCS desktop or UgCS for DJI 1. Use UgCS desktop to track vehicle’s telemetry data.

2. Use UgCS for DJI to control camera.
3. Use both applications to change control mode or failsafe command performance (return to home).

8 Take pictures or record video UgCS desktop or UgCS for DJI Use remote controller or dedicated buttons in UgCS for DJI application to make a shot or start/stop recording of video.



288.png



*NOTE: Minimal time interval between taking pictures is different for different DJI drones. If the time interval is too short, an error message will be displayed. 
9 Сonfigure camera UgCS for DJI The parameters of camera can be modified in „Camera settings”.



29.png



10 Take photo placemark UgCS for DJI If “Make a placemark on photo” is checked in UgCS for DJI Settings menu, use remote controller or dedicated buttons in UgCS for DJI application to make a photo placemark.



WhatsApp Image 2019-04-01 at 13.16.39.jpg



11 Land UgCS desktop or UgCS for DJI Phantom 3 and Inspire 1 support Land mission command in UgCS desktop. Use Return to Home command in UgCS for DJI.



300.png



*NOTE: Manoeuvre the aircraft during landing to avoid obstacles.
12 Click & Go UgCS desktop or UgCS for DJI Enables to interactively command the aircraft to fly to a location by clicking on the map. See Click & Go section for more information.
13 Joystick UgCS desktop (UgCS for DJI in future releases) Control vehicle with joystick.
14 Return Home UgCS desktop or UgCS for DJI Enables to interactively command aircraft to fly to a home location. Maneuver the aircraft to avoid obstacles, when returning home.
*NOTE: If the vehicle is within 30m from Home position it will land immediately.